Compare to hammer crusher,impact crusher has bigger reduction ratio and can fully use the high speed impact energy of entire rotor.But because the impact crusher board hammer is extremely easy to wear, it also is restricted in the hard material stave application.Impact crusher is usually used to break thick garrulous, garrulous or the limestone, the coal, the calcium carbide, the quartz, the dolomite, the curing iron ore, the gypsum and the industrial chemicals which are hard following brittle material.
The word impact makes sense that in this particular type of crusher some impaction is being used for crushing of rocks.In normal types of crusher pressure is generated for the crushing of rocks.But, impact crushers involve an impact method.
Dsmac, china largest impact crusher manufacturer, has started to enlarge its production area on april 23th, and the whole project schedulelasted for three months, which could be ended on july 23th.The production capacity will be doubled to reach annual production value of 800 million.
General machine primary impact crushers, crush the stone medium hardness (with less abrasive) , as controlled, do the primary level.1300 mm with a weight of 3000 kg of stone, it is possible to decrease the 0-100 mm with primary impact crusher.Stone into the crusher, stone by stone before impact with the shock of the impact plates on the rotor's upper wing and then crushs into the strike plate on the lower wing.Crusher main body is in two parts, the upper part of the hydraulic crusher maintenance completely open with strike plate and cylinder liners palette tests are done easily possible to change.
Mclanahan impact crushers are found in a wide variety of applications.The most common is processing limestone, but any sedimentary stone and some metamorphic stone are suited for impact crushing.Impactors also operate in manmade materials with similar characteristics as sedimentary stone.Even in some rather abrasive materials, like steel slag and demolition concrete rubble, impactors are the favored means to attain a repurposed and value-added product.In quarry operations, the use of impactors also provides a means to remove deleterious minerals.If the feed material includes soft stone, the impact force will reduce the soft stone finer than the harder rock.A screening process will then allow the soft deleterious material to pass through and out of the flow to the rest of the plant.
The aggregate industry (cement, ready-mix concrete, asphalt, crushed stone, sand & gravel), wants to process rock, sand, and gravel into a salable product as efficiently and inexpensively as possible.One such way to process these materials is sending gravel, rock, and sand through an impact crusher, which breaks up the material by either striking it with a rapidly moving blow bar or by throwing it into a stationary anvil where it breaks upon impact.Impact crushers may be used as primary, secondary, or tertiary crushers depending on the producers final-product-size needs.Impact crushers are available in stationary, track, and portable configurations meeting any demand for any of these industries.Although impact crushers generally have a higher operating cost than other crushers, they tend to produce a more uniform particle shape (cubical) which is desirable and produce more fines for hot asphalt producers.Common types of impact crushers are horizontal shaft impactor (hsi) and vertical shaft impactor (vsi).While the ultimate design of each type of impactor is to crush rock, their methodologies differ.Horizontal shaft impactors (hsi) consist of a hopper, two or three aprons (curtains), a rotor, and hammers (blow bars).Essentially, large products are fed into the hopper where they come into contact with hammers on a spinning rotor which crushes the material into smaller pieces.As the larger material gets impacted by the hammers it comes into contact with each apron rebounding it back to the rotating hammers for another round of impacting until it is discharged out of the hsi.Hsi gradation is controlled by rotor speed, the more speed the finer the output; apron gap settings, the smaller the gap the finer the gradation; the number of hammers, depends on crusher speed.Rotor construction can be open or solid, cast or fabricated ceramic.If the impactor is used in the primary position, a massive solid rotor is advised due to its high inertia for optimum crushing performance and solid backing support for the hammers resulting in longevity and lower costs.If the impactor is in the secondary or tertiary position, then efficient open style rotors and heavy gravity hung aprons will deliver consistent performance when crushing aggregates or recycled asphalt products.Hammers are a critical part when it comes to crushing with horizontal shaft impactors.The metallic composition of the hammers matters greatly; choosing the wrong bar for your application may decrease production, and increase repair/replacement costs.The hammers can be made from the hybrid alloy, manganese, low chrome, high chrome, and high chrome ceramic.Below are the best-suited applications per hammer material:high chrome: asphalt, highly abrasive materials, smaller feed sizemedium chrome: most steel contaminants, some asphalt, larger feed sizelow chrome: concrete, demolition, aggregates, heavy steel contaminants, very large feed sizemanganese: abrasive materials, asphalt, concrete, light aggregates, some steel or rebar contaminants, larger feed sizevertical shaft impactors (vsi) consist of a feed hopper, feed tube, a rotor, and either stationary anvils or rock shelves.Essentially, feed material drops through the feed tube into the rotor, which, through centrifugal force, throws the material against stationary anvils made up of composite metal alloys or rock shelves.When the rock impacts the anvils or rock shelves, it shatters along natural stress lines, creating a uniform, cubical product.This method is both economical and simple to operate.The vsi has the best rate of production of smaller sizes (- ) as it is the only crusher that does not close off the discharge side to make a smaller product.But are also limited in feed size both by the feed tube and table configurations.Impact crushers produce the most uniform cubical shape for finished products, due to its consistent ability to uniformly break apart aggregates through striking.Striking can be done with rapid moving hammers as seen on the horizontal shaft impactor or being thrown against an anvil or rock wall as seen on the vertical shaft impactor.Impact crusher machines are available as stationary, track, or mobile units, and can be used in the primary, secondary, or tertiary position in the producers line up.Impact crushers can be subject to high wear and operating costs and high production of fines.View telsmith impactors.
Copyright© 2020 DRiveOn machinery.All rights reserved. Sitemap