Jaw Crusher Spring Assembly

Therefore, when crushing hard rocks and long rocks, the cone crusher should be preferred.This design is more favorable.When wet and viscous ore is crushed, or medium, small concentrators, jaw crushers are suitable.

Firstly, before use a jaw crusher, you should check whether there is foreign matter in the crushing cavity.If there are some foreign matter, it is necessary to timely clear them up and then start the machine, otherwise it will cause damage to a jaw crusher because of the excessive load when starting the motor.

Jaw crusher working principlejaw crusher adopts the electric motor as the power.The eccentric shaft is revolved by an electric motor through v-belts.It causes the swing jaw following the preconcert path to crush the feeding material.Thus the material will be crushed in the crushing chamber which is composed of the stationary jaw plate, swing jaw plate and the liner plate.The material is discharged from the lower part of machine that is what you want.

Flywheelsone piece cast flywheels in 48 or 60 diameter sizes.Hydraulic jaw adjust with shims jaw crusher settings can be easily changed with our standard hydraulic pump used to take the pressure off.This allows you to add or remove shims as needed for the correct setting.

The third, if the flywheel has deviation from the slot position in use process of jaw crusher, it will make the machine unbalance.So that the machine happen shaking phenomenon.

Working principle: taking the fixed jaw concrete crusher machine as an example, the pe and pex series fixed jaw crushers are powered by electric motors.The eccentric shaft is driven by the v-belts and the sheaves through the motor pulleys so that the moving jaws can reciprocate according to the predetermined trajectory.The materials that enter the crushing chamber consisting of the fixed raft, the movable raft, and the sidelining is crushed, and the finished material is discharged through the lower discharge opening to obtain the material you want.Tips for daily maintenance:.

During the working process of the sand making production line, the large stone material silo is evenly fed into the jaw crusher by the vibrating feeder for coarse crushing.The coarsely crushed stone material is sent to the cone crusher by the belt conveyor for medium crushing.The crushed stone is sent to the vibrating screen by the belt conveyor for screening.The finished sand is sent to the sand washing machine by the belt conveyor and then sent to the finished material pile through the belt conveyor; the large grain stone is sent to the standing by the belt conveyor.The impact crusher is finely crushed, and the finely crushed stone is again sent to the vibrating screen by the belt conveyor for screening, thus forming a closed circuit for multiple cycles. advantages of gravel aggregate production line: 1.Full-automatic operation process, higher production efficiency, more optimization of work efficiency, high automation degree, large crushing ratio, high production efficiency, large processing capacity, after crushing products are cubic, needle-like content is low, no internal cracks, high compressive strength.2.More widely and successfully applied in the crushing of limestone, basalt, granite, cobble and other rocks.The quality of the crushed products can meet the standards, which provides qualified aggregate for the industries of highway, railway, water conservancy, concrete mixing station and so on.3.It can be used for aggregate and artificial sand of hard limestone, granite, basalt, river pebble and other materials.It is widely used in hydropower, building materials, highway, urban construction and other industries.According to different process requirements, various types of equipment are combined to meet the different process requirements of customers.

1) so that the material in the crushing cavity is" laminated crushing" at a certain extent by the use of " fixed volume" type linear -- modified gauss curve advanced crushing cavity of professor dai shaosheng.What's more, the pure pressure of crushing effect is five times of the shear stress, the material in the crushing cavity is repeatedly laminating crushed, which leads to the obvious improving of the crushing effect of jaw crusher, also promote a high crushing efficiency and discharge average particle size up to 5-10mm.

Jxsc has received malaysia customers visiting our factory, for checking the iron ore washing plant, including jaw crusher, log washer, belt conveyor, vibration screen, trommel screen, feeding machine,ect.

E.M.U.S ms561 location cairns, qld machine type - tracked jaw crusher make fintec model 1107 year 2005 hours 7138 machine specs (approx.) crusher 1100 x 700mm (44 x 28) sandvik jaw, hopper capacity 7m3 (9.2yd3), main conveyor 1000mm 3 ply extra heavy duty (42), side conveyor 650mm 3 ply (26), weight 42.5 tonnes, recommended setting range 40 - 125mm (11 /2 - 5), recycling only 75 - 175mm (3 7) quarrying only spec sheet available on request maintenance or.

River gravel sand production line equipment:river gravel sand production line usually consists of vibrating feeder, jaw crusher, impact crusher (sand making machine), vibrating screen, sand washing machine, belt conveyor, centralized electric control equipment; design production 50 -500 tons / hour.

This is not practical in a jaw crusher.Magically the engine (jaw crusher) is already setup with the actual parts in place.All you need to do is balance it.Not so easy.

NEED A QUESTIONS?

If you are interested in our products, or have any questions for us, you can click the button below

Contact Us

Your demand

Contact Information

Zhengzhou High-tech Zone, China

[email protected]

Related Blogs

Copyright© 2020 DRiveOn machinery.All rights reserved. Sitemap