Sonic Earplete With Microphone For Grinding Ball Mill

4.The fluid energy mill involves __________a) pressureb) temperaturec) fluidd) densityview answeranswer: aexplanation: the fluid energy mill usually uses compressed air and super-heated steam admitted at a pressure of 7 atm through nozzles.5.At what speed stirred mill operates?a) 50 to 500 rpmb) 5 to 10 rpmc) 10 to 500 rpmd) 100 to 1500 rpmview answeranswer: dexplanation: in a stirred mill, a central paddle wheel or impellor armature stirs the media at speed from 100 to 1500 rpm.Advertisement freestar.Queue.Push(function () { googletag.Display('sanfoundry_300x250_320x50_320x100_inlist2'); }); 6.What does colloid mill produces?a) emulsions and solid dispersionsb) wet and dry productsc) coarse and fine particlesd) broad particlesview answeranswer: aexplanation: colloidal suspensions, emulsions and solid dispersions are produced by means of colloid mills or dispersions mills.7.The clearance between rotor and stator is ______a) 5 to 10 mmb) 1 to 2.5 mmc) 0 to 1.25 mmd) 5 to 15 mmview answeranswer: cexplanation: the mill consists of a flat rotor and stator, the clearance between the rotor and stator is generally 1 to 1.25 mm.8.The power consumption of colloid mill is _______a) very lowb) optimumc) criticald) very highview answeranswer: dexplanation: the power consumption is very high and the material should therefore be ground as fine as possible before it is fed to mill.9.The speed of a rotary knife cutter is ___a) 100 to 500 rev/minb) 200 to 900 rev/minc) 400 to 600 rev/mind) 50 to 60 rev/minview answeranswer: cexplanation: a rotary knife cutter contains a horizontal rotor turning at 200 to 900 revolutions per minute, which is cylindrical chamber.10.______ indicates the impact of resistance.A) toughnessb) rigidityc) brittlenessd) fatigueview answeranswer: aexplanation: toughness indicates the impact of resistance.It is the inverse of friability and brittleness, it is also a deciding factor for commutation.Advertisement freestar.Queue.Push(function () { googletag.Display('sanfoundry_300x250_320x50_btf_1'); }); sanfoundry global education & learning series mechanical operations.To practice all areas of mechanical operations, here is complete set of 1000+ multiple choice questions and answers. prev page - mechanical operations questions and answers intermediate and fine crushers next page - mechanical operations questions and answers advantages of ball mill.

The ball mill is equipped with a cylindrical rotating device and two bins, which can rotate by gears.The discharge port is straight, and there are also air intake devices, dust exhaust pipes, and dust collectors.

Steane, r.A., and hinckfuss, d.A., 1978, selection and performance of large diameter ball mills at bougainville copper ltd., paper no.36, proceedings of the eleventh commonwealth mining and metallurgical congress, hong kong.

(3) the ball mill uses a rubber liner instead of a manganese steel liner.The noise level can be reduced by 9db (a), and the frequency spectrum characteristics of the ball mill are also changed from high frequency to low frequency.Ball mill design soundproof room.

1.High efficiency of grinding.Using the principle of material bed's crushing and squeezing, the material is rolled, cut, impacted in the mills; the airflow in the mill can take the grinded materials out timely to avoid excessively grinded; the materials generally stay in the mill for 2-4 minutes.It has the 165% grinding efficiency as the ball mill and the power consumption can be reduced by 30% or so.

We are out of stock of all continuous ball mills.We are always looking to buy high-quality, used continuous ball mills.

2.Add an efficient classifier.The particle size of the abrasive material is reduced, and the powder selection efficiency is improved.If the efficiency of the grinding system is low, it not only affects the output of the ball mill, but also affects the quality of the cement.

Batch ball mills plant.Either wet grinding or dry grinding may be conducted in the batch ball and rod mills.Usually, wet grinding is more efficient than dry .

The design is pretty simple.A ball mill consists of a cylindrical shell that rotates around its own axis.Inside the shell, you will notice stainless steel or rubber balls, also known as media.The inner surface of the cylindrical shell is coated with material which is abrasion-resistant in order to protect the shell from the constant ball hitting.As there are different ball mills on the market, the design can vary.Each ball mill has different size and rotating ratio.Its up to you to decide, which one fits your budget and job requirements.

Nov 22 (reuters) - copper mountain mining corp : * reports ball mill transformer interruption * says one of the two abb transformers powering the motors on ball mill #2 at.

Used- paul o.Abbe ball mill, model 6pm (clm 94), brick lined.Approximate 29" diameter x 32" straight side.Approximate 12.5 cubic foot capacity (94 gallon).Approximate 9-1/2" x 8" charge/discharge with cover.Driven by a 5 hp, 3/60/208-230/460 volt, 1750 rpm thru flak reducer, 24.99:1 ratio.Mounted on carbon steel stands.In more info.

Ball mill is extensively used for milling different types of ores or rocks in metaland non-metal mining and building material industry.The main bearing ofthe ball mill using the shell diameter 900-2100mm is spherical linerbearing; for the shell diameter 2700mm, the main bearing is completelyclosed self-aligning 120??bearing with powerful alloy of substantial lead and lowtin with low hardness, underneath laid with cooling copper piping fullof water the bearing is of static strain structure with substantial and lowpressure united oil lubricating system.

NEED A QUESTIONS?

If you are interested in our products, or have any questions for us, you can click the button below

Contact Us

Your demand

Contact Information

Zhengzhou High-tech Zone, China

[email protected]

Related Blogs

Copyright© 2020 DRiveOn machinery.All rights reserved. Sitemap